USDA Feasibility Study for Sawmills and Wood Products in New Hampshire

    NAICS 321

    Wood products are one of the most rural industries in New Hampshire. Of the state's 109 wood product manufacturers with paid staff in 2023, 73, or 67.0 percent, were in non-metro counties, and the state's density of 7.8 plants per 100,000 residents is 1.88 times the national figure. The count held steady from 2019 to 2023 while the industry shrank 2.3 percent nationally. A USDA feasibility study for a New Hampshire sawmill, pallet plant, millwork shop or engineered wood producer has to show log or lumber supply at a sustainable price, buyers for every product stream including residuals, equipment economics that justify the term, and a workforce in counties where the mill is often a leading employer.

    What follows covers the state's wood plants by county, their SBA history, B&I terms, two worked loans, and what USDA Rural Development will expect a lender-grade study to establish.

    Wood products in New Hampshire: market evidence

    New Hampshire: wood product manufacturing, supply and rural footprint

    MeasureNew HampshireUnited States
    Establishments, 2019 → 2023108 → 109 (+0.9%)14,223 → 13,899
    Per 100,000 residents (2023)7.84.1
    Average employees per establishment18.731.1
    Average annual pay per employee$62,136$57,420
    Share of establishments in non-metro counties67.0% (73 in 7 counties)
    Share of state population in non-metro counties (2025)36.9%

    Non-metro counties with the most wood product manufacturing (2023): Merrimack County (17); Cheshire County (16); Grafton County (15); Sullivan County (11); Coos County (6); Carroll County (5).

    Sources: U.S. Census Bureau, County Business Patterns 2019 and 2023 (state and county files; establishments with paid employees; employment and payroll suppressed in some cells); Vintage 2025 county population estimates; OMB metropolitan statistical area delineation, July 2023. Non-metro county is a proxy for USDA rural eligibility, not the eligibility test itself.

    Reading the wood products data. The Census category covers sawmills, planing and treating, veneer and engineered wood, millwork, containers and pallets, and manufactured and prefabricated wood buildings, so the 109 plants are a mix. They are small: 18.7 employees on average against 31.1 nationally, and payroll of $1,159,495 per plant against $1,785,760. Pay per employee is $62,136, 8.2 percent above the national $57,420. A small mill paying above-average wages has thin room for error in its cost per thousand board feet, and a reviewer will ask whether the project's throughput gains justify the capital. The stable count in a shrinking national industry is a point in the state's favour, but it says nothing about whether a specific mill has secure log supply and buyers.

    Wood plants by county

    CountyOMB 2023 statusWood product plants, 2023Residents, 2025Per 10,000 residents
    Merrimack Countynot metro17158,0781.08
    Cheshire Countynot metro1678,2692.04
    Grafton Countynot metro1593,2251.61
    Rockingham Countymetro14324,0770.43
    Hillsborough Countymetro13433,4150.30
    Sullivan Countynot metro1143,9612.50
    Strafford Countymetro9135,0430.67
    Coos Countynot metro631,3431.91
    Carroll Countynot metro552,7840.95
    Belknap Countynot metro365,1470.46

    Sullivan County is the densest at 2.50 plants per 10,000 residents, followed by Cheshire (2.04), Coos (1.91) and Grafton (1.61). Merrimack has the most plants, 17, with Cheshire at 16 and Grafton at 15. In Hillsborough the density falls to 0.30. For lenders, the pattern means wood plants are usually sited where timber is close and labour markets are small, so recruitment and the plant's role in the local economy both belong in the study.

    Supply, markets and the mill's economics

    A wood products study begins with raw material: timber supply within the haul radius, competing mills and their consumption, stumpage and delivered log prices, and the reliability of loggers and truckers. On the market side it documents buyers for lumber grades, timbers, pallets, millwork or building components, plus outlets for chips, sawdust, bark and shavings, whose loss can turn a profitable mill into a loss-making one. Revenue is volume by product and grade times net price; costs are logs or lumber, labour, energy, saw and equipment maintenance, kiln fuel, trucking, insurance and overhead. Capital items are the site, buildings, headrig or scanning and optimising equipment, kilns, planers, material handling, mobile equipment and working capital for log and lumber inventory.

    Rural footprint and B&I eligibility in New Hampshire

    At 14.0 plants per 100,000 non-metro residents against 4.0 in Hillsborough, Rockingham and Strafford, wood products are 1.81 times as concentrated in the non-metro counties as the population is. All seven non-metro counties have plants: Merrimack (17), Cheshire (16), Grafton (15), Sullivan (11), Coos (6), Carroll (5) and Belknap (3).

    The B&I test itself, 7 CFR 5001.3, is about the parcel: a mill is ineligible only inside a city or town above 50,000 residents or inside the urbanized area attached to one. Manchester (116,818) and Nashua (92,435) are the only New Hampshire places over the threshold, and Concord (44,597) is the only other place above 40,000. Few mills operate in those cities, so eligibility rarely blocks a wood products project; the 36 plants in the metro counties are mostly in smaller towns. Confirm the site anyway, using the place list on the New Hampshire state page.

    Program fit for a New Hampshire wood products plant

    B&I is a natural fit: acquisition of a mill, new lines, scanning and optimisation equipment, kilns, expansion and working capital, with guarantees up to $25 million. SBA has played a small role, 15 7(a) loans and 4 504 loans since FY2010, the most recent a single 7(a) loan of $462,500 in FY2024 to FY2026, so B&I is likely to be the larger tool for a serious capital programme. REAP can fund biomass boilers for kilns, solar or efficiency upgrades at an operating mill, though the grant is now a reimbursement after a year of operating data. Mills, as private manufacturers, sit outside Community Facilities. Under Part 5001, a lender should be ready to show that the project does not simply move jobs or capacity from another mill and that added capacity is not going into an oversupplied market.

    Financing benchmarks: USDA B&I next to SBA

    New Hampshire: SBA lending to wood product manufacturing

    Period7(a) loans7(a) dollars504 loans504 dollars
    FY2010 to FY20167$1.1 million4$1.1 million
    FY2017 to FY20195$1.2 million0$0
    FY2020 to FY20232$1.1 million0$0
    FY2024 to FY20261$462,5000$0

    Average 7(a) loan, FY2020 to FY2026: $518,833. New Hampshire had fewer than 30 seasoned 7(a) loans for wood product manufacturing; nationally, 7.1% of 1,015 FY2010 to FY2016 loans were charged off, on average 65 months after approval.

    Source: SBA 7(a) and 504 FOIA loan data, as of 30 Sep 2026 (project state; disbursed loans only; cancelled and undisbursed loans excluded).

    TermUSDA B&I, fiscal 2026Source
    Guarantee, loans under $5 million85%91 FR 11272
    Guarantee, $5 million to $25 million80%91 FR 11272
    Upfront guarantee fee3.0% of the guaranteed amount91 FR 11272; 7 CFR 5001.454
    Annual retention fee0.55% of the guaranteed share of principal outstanding on December 3191 FR 11272; 7 CFR 5001.455
    Reduced-fee loans (criteria in 5001.454)1.0% fee, 0.50% retention, 80% guarantee91 FR 11272
    Guarantee issued before construction is completeadditional 0.50% fee91 FR 11272; 7 CFR 5001.454
    Maximum loan per borrower$25 million7 CFR 5001.406(c)
    Termuseful life of the collateral, 40 years at most, no balloon7 CFR 5001.402
    Interest ratenegotiated, fixed or variable, no higher than the lender's similar non-guaranteed loans7 CFR 5001.401
    Equity, existing business10% balance sheet equity (or debt to equity of 9:1), or 10% of project cost7 CFR 5001.105(d)(1)
    Equity, new business20% balance sheet equity (or 4:1), or 25% of project cost; 25% (or 3:1) when the guarantee issues before construction is complete7 CFR 5001.105(d)(3), (d)(4)
    Independent feasibility studyrequired above $1,000,000 for a new business; at the Agency's discretion otherwise7 CFR 5001.306(a)(3)
    SBA 7(a), for comparison85% guarantee up to $150,000, 75% above13 CFR 120.210
    SBA 504, for comparisonborrower injection 10%; 15% if new or single purpose; 20% if both13 CFR 120.910

    What the SBA history tells a wood products lender. With 19 SBA loans in 17 years, 0.71 percent of the U.S. total for the asset, New Hampshire's record shows lenders financing wood plants occasionally and at modest size. The three 7(a) loans since FY2020 averaged $518,833, a sample too thin to anchor an example; Loan A below therefore starts from the national mean for the same years, $766,800, rounded to $770,000. The industry's national loss record is poor, 7.1 percent of 1,015 seasoned loans written off, typically five and a half years after approval, so a reviewer will look closely at raw material and market risk. Federal award data add little: USAspending, which can miss awards, shows no B&I loan of any kind in New Hampshire in the last three fiscal years.

    Worked example (illustrative)

    Loan A, $770,000, rounds the national average wood products 7(a) loan. Loan B, $3,500,000, is an illustrative modernisation of an existing mill: scanning, optimising and kiln capacity. Each is priced at an illustrative 7.25 percent, fixed (5001.401), and amortized over 15 years (5001.402) because saws, scanners and kilns wear out well before the mill building.

    Input or resultLoan A (national average)Loan B (illustrative modernisation)
    Loan amount$770,000.00$3,500,000.00
    Guarantee percentage (fiscal 2026 tier)85%85%
    Guaranteed amount$654,500.00$2,975,000.00
    Unguaranteed amount (lender's own risk)$115,500.00$525,000.00
    Upfront guarantee fee (3.0% of the guaranteed amount)$19,635.00$89,250.00
    Upfront fee if the guarantee issues before construction is complete (3.5%)$22,907.50$104,125.00
    First annual retention fee (0.55% of the guaranteed share of the balance after 12 payments)$3,461.88$15,735.82
    Interest rate (illustrative, fixed)7.25%7.25%
    Amortization (years, no balloon)1515
    Monthly payment$7,029.04$31,950.20
    Annual debt service (NOI at 1.00x)$84,348.53$383,402.41
    NOI needed for 1.25x coverage$105,435.66$479,253.01
    Coverage at that NOI if the rate is 2 points higher1.11x1.11x
    Coverage at that NOI if amortization is 5 years shorter0.97x0.97x
    New business equity, 25% of project cost (5001.105(d)(4))$256,666.67$1,166,666.67
    Total project cost on that basis$1,026,666.67$4,666,666.67
    New business equity, 20% balance sheet route if this loan is the only liability$192,500.00$875,000.00
    Existing business equity, 10% of project cost (5001.105(d)(1))$85,555.56$388,888.89
    Independent feasibility studyAgency discretion (5001.306(a)(3)(ii))required for a new business (5001.306(a)(3)(i))

    Income per thousand board feet. If Loan B supports an illustrative 8 million board feet a year, 1.25x coverage needs $59.91 of net operating income per thousand board feet, of which $47.93 goes to debt service. Loan A at an illustrative 2.5 million board feet needs $42.17 per thousand. For a plant of the state's average size, 18.7 employees, Loan B's target equals $25,628.50 per employee, 41.3 percent of the average New Hampshire plant's payroll. Term is critical: if the lender holds Loan B to 10 years because most collateral is machinery, the same income covers debt service only 0.97 times, below break-even. A two-point rate rise at 15 years leaves 1.11x. An existing mill meeting the 10 percent of cost test puts in $388,888.89 on a $3,888,888.89 project. Volumes are illustrative.

    What a lender-grade sawmill and wood products feasibility study in New Hampshire must prove

    1. Timber or lumber supply within the haul radius, with competing consumption and delivered price history.
    2. Buyers for each product and grade, with contracts or letters where they exist.
    3. Outlets and prices for chips, sawdust, bark and shavings, and the effect on margin if one closes.
    4. Throughput and recovery gains from new equipment, verified against vendor specifications.
    5. Labour at New Hampshire pay ($62,136 per employee on average) in counties with small labour pools.
    6. Working capital for log and lumber inventory through seasonal harvest patterns.
    7. An equipment-life schedule that supports the requested amortization under 5001.402.
    8. Environmental, air and fire safety permitting for kilns, boilers and dust collection.
    9. Evidence that the project adds net capacity or jobs rather than moving them from another location.

    Risks and mitigants in New Hampshire

    Raw material risk comes first: log prices and availability move with weather, harvesting conditions and competing demand, so the study should test a higher delivered log cost. Market risk follows, because lumber and pallet prices swing with construction and freight cycles. Loss of a residuals buyer can turn a mill's by-products from income into a disposal cost. Fire, dust and equipment failure are operational risks requiring insurance and maintenance budgets. Labour availability in rural counties limits shifts. Used sawmill machinery sells into a thin market, and USDA's appraisal rules (5001.203) take out going-concern value before any discount, which pushes lenders toward real estate and personal guarantees for security.

    Process, documents and what gets a study returned

    The study travels with the lender's B&I request to Rural Development's state office for New Hampshire. A mill operator supplies historical financial statements, production and recovery records, log supply agreements or procurement history, customer and residuals contracts, equipment quotes and installation schedule, permits held, and the owners' financial statements and guarantees. USDA's questions usually follow when they assume recovery gains without evidence, ignore residuals markets, treat lumber price peaks as normal, or request a term longer than the equipment's life.

    Program example

    National program example (outside New Hampshire): one of the site's published case studies follows a hardwood mill modernisation in the Pennsylvania Wilds financed with USDA support, in the $2 million to $15 million range, linked below. No New Hampshire wood products loan under B&I is documented in the inputs.

    Hiring a USDA sawmill and wood products feasibility study consultant in New Hampshire

    Under 5001.306(a)(3)(i), a start-up wood company borrowing above $1,000,000 on a B&I guarantee has to file a study whose author is independent, qualified and accepted by USDA, which also decides what it covers. A modernisation by an operating mill is in USDA's discretion under 5001.306(a)(3)(ii), and given the industry's national loss rate a lender will usually want one for a project like Loan B. The right USDA feasibility study consultant for a mill understands timber supply and residuals markets as well as lumber prices, and has no tie to the equipment vendor.

    The site's cost page lists what is included: the five Part 5001 components, a five to ten year projection with sensitivity analysis, market area and demand drivers, competitive supply and capture modelling, comparable operator benchmarks, the management assessment, a PDF and Word report, the Excel workbook, a kickoff call and a midpoint review, one round of revisions and the written acceptance guarantee. Engineering and construction cost estimating beyond high-level benchmarking are separate. A standard B&I study is fixed at $6,900 to $12,500 and runs six to seven weeks; projects over $10 million or with limited comparable data move to the complex tier.

    To scope a mill study, use the contact page. Describe the plant's location, program, cost and lender status, and a senior analyst follows up within one business day under the page's stated standard.

    Last updated 2026-11-08

    David Miller, CPA

    USDA Feasibility, Inc.

    Frequently Asked Questions

    When does a New Hampshire sawmill or wood plant need a USDA feasibility study?

    A newly formed wood company asking for more than $1,000,000 under B&I has no choice: 7 CFR 5001.306(a)(3)(i) makes the independent study a condition. For an operating mill, or a loan of $1,000,000 or less, USDA may require one under 5001.306(a)(3)(ii). Given the 7.1 percent national loss rate on seasoned wood products loans, most lenders want a study for any significant equipment programme.

    What does a sawmill feasibility study consultant cost?

    Expect $6,900 to $12,500, fixed, for a single mill with a loan between $1 million and $10 million, the cost page's standard band; a modernisation above $10 million, a phased programme or a plant with few comparable operators moves to the complex tier, $10,500 to $14,500. On Loan B, the B&I upfront guarantee fee alone is $89,250.00.

    How long does a wood products feasibility study take?

    Plan for roughly a month and a half on standard terms, longer for complex work, based on the cost page. Wood products studies often need direct interviews with log suppliers, residuals buyers and comparable mills, which the cost page treats as primary research. Rush delivery in three to four weeks is available at a premium when capacity allows.

    Who can prepare a USDA wood products feasibility study?

    Someone with forest products expertise and no link to the mill, its saw and kiln suppliers, its log sources, its buyers or its lender, whom USDA is willing to accept. A vendor's throughput projection or a buyer's letter is evidence for the study, not a replacement for it. USDA keeps no approved list; the state office judges acceptability during its review.

    How long is a sawmill feasibility study valid?

    Part 5001 sets no expiry. USDA generally looks for market data within about 18 months, according to the site's cost page, and appraisals under 5001.203 must be less than a year old at closing. Lumber and log prices can move sharply within a year, so update the price assumptions if closing is delayed or markets shift.

    Can one wood products study serve SBA and USDA lenders?

    Yes. SBA lenders may demand a study (13 CFR 120.160(b)), and a report prepared to USDA's standard satisfies them. New Hampshire wood plants have taken 15 7(a) and 4 504 loans since FY2010, so SBA is an option for smaller projects. Keep one model and name both lenders as intended users.

    How does a study show log supply for a New Hampshire mill?

    By mapping the haul radius, estimating the timber available within it, listing competing mills and their consumption, and showing delivered log price history and the mill's procurement record. Supply agreements with loggers or landowners strengthen the case. The study should also test a year of higher log prices or lower availability and show the effect on coverage.

    Why does the loan term matter so much for a mill?

    Because the collateral is mostly machinery with a shorter life than a building, and 5001.402 limits the term to useful life. Loan B's coverage drops from 1.25x at 15 years to 0.97x at 10 on identical income. A schedule of each machine's remaining life is the evidence that justifies the longer term.

    Are New Hampshire wood plants usually eligible for B&I?

    Usually, because they are rural: 67.0 percent are in non-metro counties, and the only places over 50,000 residents are Manchester and Nashua, where few mills operate. Sullivan County, at 2.50 plants per 10,000 residents, has the highest density. Even so, the eligibility test applies to each parcel under 5001.3, so confirm the site before ordering a study.

    Sources

    1. U.S. Census Bureau, County Business Patterns 2019 and 2023, state and county files: https://www2.census.gov/programs-surveys/cbp/datasets/
    2. U.S. Census Bureau, Vintage 2025 population estimates (state, county and incorporated places): https://www2.census.gov/programs-surveys/popest/datasets/2020-2025/
    3. Office of Management and Budget, metropolitan and micropolitan delineation, July 2023: https://www2.census.gov/programs-surveys/metro-micro/geographies/reference-files/2023/delineation-files/list1_2023.xlsx
    4. U.S. Small Business Administration, 7(a) and 504 FOIA loan data, as of 30 Sep 2026: https://data.sba.gov/dataset/7-a-504-foia
    5. 7 CFR Part 5001, OneRD Guaranteed Loanmaking and Servicing, CFR 2026 edition (govinfo): https://www.govinfo.gov/content/pkg/CFR-2026-title7-vol15/xml/CFR-2026-title7-vol15-part5001.xml
    6. 91 FR 11272, OneRD annual notice of guarantee fee rates, retention fee rates and guarantee percentages for FY2026 (govinfo): https://www.govinfo.gov/content/pkg/FR-2026-03-09/html/2026-04581.htm
    7. 90 FR 57351, OneRD guaranteed loan regulation technical amendments, December 11, 2025 (govinfo): https://www.govinfo.gov/content/pkg/FR-2025-12-11/html/2025-22567.htm
    8. 13 CFR Part 120, SBA business loan programs: https://www.ecfr.gov/current/title-13/chapter-I/part-120
    9. USAspending.gov prime award data, Assistance Listings 10.768, 10.766 and 10.868, New Hampshire, FY2024 to FY2026: https://www.usaspending.gov/search
    10. Site cost and timeline page: /usda-feasibility-study-cost; contact page: /contact

    Data current as of November 2026.

    Ready to Start Your USDA Project?

    Get your free consultation today and take the first step toward securing USDA funding for your rural development project.

    Our USDA feasibility study consultants scope every engagement against the five Part 5001 components in a free consultation.

    Get Your Free Consultation

    Fill out the form below and we'll contact you within 24 hours to discuss your project.

    We'll respond within 24 hours