Sawmill Feasibility Study for USDA B&I and Timber Production Expansion Loans

    Last updated 2026-11-08

    Short answer

    A sawmill feasibility study is the independent report that tells a lender and USDA whether a mill can buy enough logs at a workable price, turn them into lumber and residuals at the planned recovery, sell both through a full lumber price cycle, and still cover its debt. For a USDA Business and Industry (B&I) guaranteed loan over $1,000,000 to a new business, a study by an independent qualified consultant is required; on smaller loans or expansions, USDA or the lender may still ask for one [1]. Mills near high-priority National Forest land may instead use USDA's Timber Production Expansion guarantee, which runs under the same Part 5001 rules with a 90% guarantee and no guarantee fees [2].

    Sawmills are among the most rural of all industries. County Business Patterns counted 2,685 sawmills with paid employees in 2023 (-2.8% since 2019), employing 79,837 people at $60,610 on average; 68.5% of those the county file places sat in non-metro counties, against 13.6% of the population [3][4][5]. The wider wood products industry (NAICS 321) had 13,899 plants. SBA lenders made 324 loans worth $208.6 million to sawmills from FY2010 to FY2026, and 11.3% of the seasoned 7(a) loans were charged off [6]. Data current as of November 2026.

    QuestionAnswer
    Is a study required?Yes for a B&I or Timber Production Expansion loan over $1,000,000 to a new business; otherwise at USDA or lender discretion [1][2]
    Which USDA guarantees fit a mill?B&I (85% under $5 million, 80% to $25 million, 3.0% fee) [7]; Timber Production Expansion (90%, no guarantee or retention fees, up to $25 million) [2]
    Does log supply from timberland count against B&I?Forestry is agricultural production, but forestry businesses are exempt from the 50% or $5 million cap on that part of a loan [1]
    Average SBA sawmill loan, FY2020 to FY2026$820,386 across 91 loans [6]
    Seasoned SBA loss benchmark18 of 159 sawmill 7(a) loans from FY2010 to FY2016 charged off (11.3%) [6]
    Safety rule specific to millsOSHA 29 CFR 1910.265 covers log and lumber handling, sawing, dry kilns, yards and waste disposal [8]

    This page sits under the site's industrial and manufacturing feasibility study hub. State-level sawmill and wood products pages are listed in the by-state section below.

    What a sawmill feasibility study is, and when USDA requires one

    Part 5001 defines a feasibility study as a report with an opinion or finding by independent qualified consultants on the economic, market, technical, financial and management feasibility of the project, organised under appendix A [1][9]. A business is new if it has operated less than a full year, or longer without reaching stable operations, including a new affiliate moving into a new location with new market or labor areas [1]. A mill restart under new ownership, a greenfield mill and a logger building a first mill are new businesses; a 30-year-old mill adding a kiln is not.

    Financing routeFeasibility study ruleSource
    B&I loan over $1,000,000 to a new businessRequired, by an independent qualified consultant acceptable to the Agency; Agency sets scope5001.306(a)(3)(i)
    B&I loan of $1,000,000 or lessAgency may require one when the lender's analysis is not sufficient5001.306(a)(3)(ii)
    B&I loan of $600,000 or lessStreamlined application if the lender's analysis is sufficient5001.306(b)
    SBA 7(a) or 504SBA may require a feasibility study13 CFR 120.160(b)
    Guarantee issued before construction completionBudget and timetable confirmed by a qualified independent consultant5001.205(e)(2)
    Timber Production Expansion guaranteeAdministered under 7 CFR 5001 (so 5001.306 applies as for B&I); feasibility studies and business plans are eligible uses of loan funds89 FR 104972

    The national average SBA sawmill loan, $820,386, sits below the $1,000,000 line, but the USDA mill projects in the program examples below are larger: a new head rig, edger, trimmer and kilns, or a restart with working capital, quickly passes $1 million. A study is also eligible for financing: B&I and Timber Production Expansion both allow loan funds to pay for feasibility studies and business plans [1][2].

    What a lender-grade sawmill feasibility study must prove

    #What the study must proveEvidence a reviewer expects
    1Logs are available in volume, species and grade within haul distanceTimber inventory and growth in the wood basket, harvest history, supply agreements, Forest Service sale schedule
    2Log cost per thousand board feet holds against competing millsDelivered log prices, competing mill capacity and buying radius
    3The mill converts logs to lumber at the planned recoveryScale method, overrun or lumber recovery factor, grade yield from the equipment vendor and comparable mills
    4Lumber sells through a full price cycleProduct mix, buyers and distribution, price history for the mill's species and grades
    5Residuals have buyersContracts or letters for chips, sawdust, shavings and bark; pellet, pulp or biomass outlets
    6Kiln and planer capacity matches sawing capacityKiln charges per year, drying schedules, planer throughput
    7The added capacity will not harm existing mills (projects over $1 million and 50 jobs)Regional mill capacity and utilisation; 5001.118(b) analysis [1]
    8Fire, dust and safety risks are controlledCompliance with 29 CFR 1910.265 [8], fire protection design, insurance quotes
    9Air and stormwater permits can be obtainedBoiler and kiln permit path, log yard stormwater plan, environmental review under 7 CFR 1970 [1]
    10Labor is available for mill and yard jobsCommute-shed labor force, wage benchmarks against Census mill pay [3]
    11Cash flow survives ramp-up and log inventory buildMonthly cash flow through start-up, log and lumber inventory financing, working capital
    12For Timber Production Expansion, raw material comes from priority Federal or Tribal landDistance to priority areas (250 miles), restoration contracts, share of raw material from Federal or Tribal land [2]

    Program fit: B&I, Timber Production Expansion, REAP and SBA

    RouteFit for a sawmillKey termsStudy trigger
    USDA B&I guaranteed loanMill construction, modernization, acquisition, equipment, permanent working capital; integrated timberland or logging [1]Up to $25 million; FY2026 guarantee 85% under $5 million, 80% above; 3.0% fee, 0.55% retention [7]Over $1 million to a new business
    Timber Production Expansion guaranteeEstablish, reopen, retrofit, expand or improve a sawmill or wood processing plant near priority National Forest land [2]90% guarantee; no guarantee or retention fees; up to $25 million; first come, first served [2]Part 5001 rules
    B&I reduced feeLocally owned and managed mill producing a natural resource value-added product [1]1.0% fee, 0.50% retention, 80% guarantee, subject to annual limits [7]Same as B&I
    REAPKiln, boiler or motor efficiency, or solar, at an operating rural millGrants after completion with 12 months of data; at most 25% of cost; $250,000 cap for efficiency [10]Technical report; study at discretion
    SBA 504Owner-occupied mill buildings and long-life equipmentBorrower 10%; 15% if new or single-purpose; 20% if both [11]SBA may require one
    SBA 7(a)Equipment, working capital, acquisitions up to $5 million75% guarantee above $150,000 [11]SBA may require one

    Timber Production Expansion is a pilot run by USDA's Rural Business-Cooperative Service for the Forest Service, authorized by section 40804(d)(3) of the Infrastructure Investment and Jobs Act and funded with more than $200 million from FY2025 [2]. Its notice defines a wood processing facility broadly: solid wood products such as lumber, posts and poles; engineered wood such as plywood, veneer and mass timber; biomass heat and power and biochar; and firewood, pellets, briquettes and liquid biofuels. Eligible borrowers can include loggers, forest workers and equipment operators who buy and process restoration byproducts [2]. Applications are scored under the B&I priority rules; the extra points the notice first offered for prior-administration priorities were withdrawn in March 2025 [2][12].

    B&I can also finance integrated wood businesses. Forestry, including timber tracts, tree farms and harvesting, counts as agricultural production, which B&I funds only when it is part of an integrated business that also processes the product and is not eligible for Farm Service Agency loans; forestry is exempt from the rule limiting the agricultural production portion to 50% of the loan or $5 million [1]. The usual ineligible uses apply: no payments above cost to related contractors, no broker fees, no rent on equipment the borrower owns, no lease payments and no distributions to owners [1].

    Eligibility: rural area, borrower and the overcapacity test

    B&I applies only in rural areas: outside cities or towns over 50,000 under the latest decennial census and their contiguous urbanized areas [1]. Most mills pass easily; the risk is a mill or remanufacturing plant on an industrial park at a metro edge. Timber Production Expansion applies its own proximity test, within 250 miles of high or very high priority land, and runs under Part 5001 [2]. Individual borrowers must be U.S. citizens or lawful permanent residents; owners of 20% or more give guarantees; and a 20% owner with a federal judgment, delinquent federal debt or a debarment makes the borrower ineligible [1].

    The test that matters most for mills is the B&I overcapacity rule. A project over $1 million that increases direct employment by more than 50 is ineligible if it would add production where there is not enough demand to employ the efficient capacity of existing competitors, unless it will not harm them [1]. Log markets are local, so a large new mill can raise log prices for every mill in the wood basket. The study should map competing mills, their capacity and buying radius, and show that timber growth and removals leave room for the new demand.

    National market evidence: wood products and sawmills

    NAICS 321 counts wood product manufacturing establishments with paid employees; sawmills are code 321113 inside it [3]. The pack figures below are for all wood products, then the detail table breaks out sawmills and their customers.

    MeasureUnited States
    Establishments with paid employees, 201914,223
    Establishments with paid employees, 202313,899
    Change, 2019 to 2023-324 (-2.3%)
    States (incl. DC) with at least one establishment, 202350
    Establishments per 100,000 residents, 20234.1
    Paid employees, 2023 (mid-March)432,255
    Annual payroll, 2023$24.82 billion
    Average employees per establishment31.1
    Average annual pay per employee$57,420
    Establishments the county file places in a county12,666 (91.1% of the national total)
    Of those, in non-metro counties4,425 (34.9%) in 675 counties
    Share of U.S. population living in non-metro counties, 202513.6%
    Rural concentration index (non-metro share of establishments / non-metro share of population)2.58

    Wood products are the most rural manufacturing subsector: a rural concentration index of 2.58 against 1.27 for all manufacturing, and 40.6% of the industry's employees work in non-metro counties [3][5]. Pay barely differs by location: $57,222 per employee in non-metro counties against $57,686 in metro counties (-0.8%), so a rural mill competes for labor at close to national industry wages.

    Sawmills and the industries that buy their lumber

    NAICSIndustryEstablishments 2019Establishments 2023ChangeEmployees 2023Avg employeesAvg payPlaced in a countyNon-metro share of those placedSBA loans FY2020-26
    3211Sawmills and wood preservation (4-digit)3,1443,051-3.0%91,68930.1$61,31759.1%65.4%104
    321113Sawmills2,7622,685-2.8%79,83729.7$60,61056.0%68.5%91
    321114Wood preservation365344-5.8%11,46333.3$66,05110.8%40.5%13
    3212Veneer, plywood and engineered wood (4-digit)1,4211,453+2.3%84,85558.4$62,56440.0%23.8%54
    321211Hardwood veneer and plywood209180-13.9%9,72354.0$53,19525.0%22.2%25
    321212Softwood veneer and plywood5764+12.3%10,993171.8$73,11431.2%30.0%0
    321213Engineered wood members (except trusses)8370-15.7%4,31261.6$68,69310.0%42.9%0
    321214Trusses803875+9.0%41,17547.1$57,48325.3%10.9%8
    321219Reconstituted wood products (OSB, particleboard, fiberboard)181177-2.2%13,58676.8$73,11114.1%36.0%10
    3219Other wood products (4-digit)9,6529,391-2.7%255,61927.2$54,31986.1%24.4%808
    321911Wood windows and doors1,1211,075-4.1%60,59756.4$61,17948.8%5.7%125
    321912Cut stock, resawing and planing779696-10.7%20,11128.9$55,02124.9%35.8%17
    321918Other millwork, including flooring1,5301,435-6.2%32,31322.5$51,83651.7%11.7%96
    321920Wood containers and pallets2,6852,786+3.8%60,76521.8$49,89863.3%16.3%180
    321991Manufactured (mobile) homes216249+15.3%26,181105.1$53,93931.3%17.9%19
    321992Prefabricated wood buildings649763+17.6%22,77329.8$55,06831.6%22.4%43
    321999All other miscellaneous wood products2,6022,326-10.6%31,36913.5$51,87556.3%18.7%328

    Sawmills fell from 2,762 to 2,685 (-2.8%), but the industries that consume lumber moved differently: wood pallet and container plants grew to 2,786 (+3.8%), truss plants to 875 (+9.0%), prefabricated wood building plants to 763 (+17.6%) and manufactured home plants to 249 (+15.3%), while cut stock and planing fell -10.7% [3]. A study should name which of these buyers sit within freight distance of the mill. The county file places only 56.0% of sawmills in a county, because counties with one or two mills do not appear; non-metro shares are computed on those placed [3].

    States with the most sawmills, 2023

    RankStateSawmills 2019Sawmills 2023ChangeEmployees 2023Avg payNon-metro share
    1Pennsylvania251239-4.8%3,263$46,50463.6%
    2Missouri159150-5.7%1,444$35,11489.4%
    3Virginia122124+1.6%3,135$48,33170.9%
    4Tennessee134121-9.7%2,277$47,26484.7%
    5North Carolina139120-13.7%4,625$62,02356.5%
    6Kentucky122115-5.7%2,059$43,71988.7%
    7Arkansas105109+3.8%4,474$63,28687.0%
    8Texas98108+10.2%3,966$68,68654.4%
    9Michigan107103-3.7%1,885$49,97593.6%
    10Washington97103+6.2%5,131$71,14248.3%
    11Wisconsin104102-1.9%1,932$50,64889.9%
    12Georgia107101-5.6%5,783$68,850100.0%

    The twelve states hold 55.7% of U.S. sawmills [3]. Hardwood states lead by count (Pennsylvania, Missouri, Virginia), while the Pacific Northwest and the South run larger mills: average employment per mill in the table varies more than fivefold. Mill pay ranges widely too, which is why the study benchmarks wages against the state and county, not the national average.

    Non-metro counties with the most sawmills

    Non-metro countyStateSawmills, 2023
    Juniata CountyPennsylvania19
    Grays Harbor CountyWashington17
    Holmes CountyOhio16
    Jefferson CountyPennsylvania16
    Crawford CountyPennsylvania15
    Reynolds CountyMissouri14
    Pike CountyOhio13
    Howell CountyMissouri12
    Mifflin CountyPennsylvania12
    Drew CountyArkansas11
    Aroostook CountyMaine11
    Shannon CountyMissouri10

    Wood products: top states by establishments and by rural share

    RankState20192023ChangePer 100k residentsAvg employeesAvg payNon-metro share*
    1California1,0661,029-3.5%2.624.3$58,7785.8%
    2Pennsylvania977981+0.4%7.521.5$51,24439.6%
    3Texas775767-1.0%2.539.2$58,25515.4%
    4Ohio563573+1.8%4.924.7$51,23353.0%
    5North Carolina601558-7.2%5.141.2$59,02735.0%
    6Florida525555+5.7%2.425.7$52,9536.7%
    7Wisconsin530521-1.7%8.838.9$56,26754.3%
    8Indiana508516+1.6%7.533.5$54,93242.4%
    9Georgia502464-7.6%4.241.5$57,47645.6%
    10Michigan474462-2.5%4.624.0$56,15742.6%
    RankStateNon-metro establishmentsEstablishments in county fileNon-metro shareState population in non-metro countiesLeading non-metro counties
    1West Virginia8911676.7%38.4%Randolph County (14); Greenbrier County (8); Pocahontas County (8)
    2Mississippi12917275.0%50.0%Chickasaw County (9); Jones County (8); Pontotoc County (8)
    3Kentucky20929670.6%37.7%Pulaski County (17); Laurel County (14); Todd County (11)
    4Arkansas16624567.8%38.0%Drew County (13); Union County (12); Hot Spring County (8)
    5New Hampshire7310967.0%36.9%Merrimack County (17); Cheshire County (16); Grafton County (15)
    6Missouri22135163.0%24.4%Howell County (24); Reynolds County (22); Shannon County (17)
    7Montana8313760.6%44.7%Flathead County (25); Ravalli County (20); Lake County (9)
    8Maine9416955.6%39.8%Aroostook County (24); Somerset County (16); Kennebec County (11)
    9Wisconsin27350354.3%25.4%Marinette County (16); Shawano County (14); Clark County (13)
    10Ohio28754153.0%17.9%Holmes County (73); Wayne County (40); Tuscarawas County (30)

    The rural-share table covers states with at least 100 wood products establishments in the county file (35 qualify) [3][5]. By count, the most non-metro wood plants are in Pennsylvania (385); Ohio (287); Wisconsin (273); Missouri (221); Kentucky (209).

    Demand drivers and competition analysis

    • Housing starts, repair and remodeling, and the truss, prefabricated building and manufactured home plants that buy framing lumber.
    • Industrial demand: pallets, crates, railroad ties, mats and blocking, which take lower grades and hardwoods.
    • Hardwood markets: flooring, cabinets, furniture, millwork and export, which pay for grade.
    • Residual markets: pulp and paper mills, pellet plants, biomass power and heat, animal bedding and mulch.
    • Log supply: timberland inventory and growth, landowner willingness to sell, logging capacity and Forest Service restoration sales.
    • Competing mills: capacity, species, products and the radius over which they buy logs.

    The competition method inventories every mill within the wood basket, normally the economic log haul radius, with species, products, capacity and condition, then compares annual timber growth and removals with the demand the new mill adds. On the selling side, it identifies the buyers within freight distance for each product and grade. A study that only lists sawmills and ignores pulp, pellet and biomass outlets misses the residual revenue that often decides coverage.

    Revenue model, key metrics and cost structure

    A sawmill earns most of its revenue from lumber and timbers by species and grade, and the rest from residuals: chips, sawdust, shavings and bark. Some mills add kiln drying, planing, treating, custom sawing or pallet stock. The model is built per thousand board feet (MBF) of output, because that is how logs are bought, lumber is sold and lenders compare mills.

    MetricWhat it measuresHow the study supports it
    Annual output (MMBF) and shiftsCapacity actually usedEquipment ratings, uptime, staffing per shift
    Overrun or lumber recovery factorLumber out per unit of log in, under the scale usedVendor data and comparable mills
    Grade yieldShare of output in higher-value gradesLog quality in the wood basket, sawing pattern
    Delivered log cost per MBFThe largest cost lineLog price history, haul distance, supply contracts
    Lumber price per MBF by productRevenuePrice history for the mill's species and grades
    Residual revenue per MBFChips, sawdust, bark incomeBuyer contracts and haul cost
    Conversion cost per MBFLabor, energy, maintenance, saws and knivesStaffing plan, tariffs, vendor maintenance data
    Kiln days and charges per yearDrying capacityKiln design and drying schedules

    The average sawmill had 29.7 employees and paid $60,610 per employee in 2023, about $1,802,219 of payroll per mill [3]. Labor, logs and energy dominate cost; insurance is material because of fire risk. Capital items are the log yard and sorting, debarker, head rig and resaw, edger and trimmer, sorter and stacker, kilns and boiler, planer, residual handling, mobile equipment, buildings, fire protection, and a working capital reserve for log and lumber inventory.

    Financing evidence: SBA lending history and seasoned losses

    SBA records give two benchmarks: all wood products (NAICS 321) and sawmills alone (321113) [6].

    Approval years7(a) loans7(a) dollarsAverage 7(a)504 loans504 dollarsAverage 504Jobs reported (both)
    FY2010 to FY20161,015$475.8 million$468,776166$120.3 million$724,55419,688
    FY2017 to FY2019450$281.8 million$626,17662$59.5 million$960,1458,389
    FY2020 to FY2023475$367.6 million$773,829118$140.9 million$1,193,9419,228
    FY2024 to FY2026331$250.5 million$756,71342$61.3 million$1,460,5954,697
    FY2010 to FY20262,271$1.38 billion$605,737388$382.0 million$984,62642,002
    ProgramApproval yearsCohort ageLoansCharged offCharge-off rate (count)Charged-off dollars / approved dollarsAverage months to charge-off
    7(a)FY2010 to FY2016seasoned (10 to 16 years)1,015727.1%4.5%65
    7(a)FY2017 to FY2019maturing (7 to 9 years)450265.8%5.0%63
    7(a)FY2020 to FY2023young (3 to 6 years)475173.6%2.3%41
    7(a)FY2024 to FY2026new (under 3 years)33120.6%0.1%22
    504FY2010 to FY2016seasoned (10 to 16 years)16631.8%1.8%59
    504FY2017 to FY2019maturing (7 to 9 years)6200.0%0.0%n/a
    504FY2020 to FY2023young (3 to 6 years)11800.0%0.0%n/a
    504FY2024 to FY2026new (under 3 years)4200.0%0.0%n/a

    Sawmills only (NAICS 321113)

    Approval years7(a) loans7(a) dollarsAverage 7(a)504 loans504 dollarsAverage 504Jobs reported (both)
    FY2010 to FY2016159$82.2 million$517,14310$6.7 million$670,2002,330
    FY2017 to FY201960$37.6 million$626,0384$7.5 million$1,869,2501,323
    FY2020 to FY202358$38.5 million$664,0479$12.4 million$1,378,8891,737
    FY2024 to FY202623$23.2 million$1,007,2351$564,000$564,000374
    FY2010 to FY2026300$181.5 million$604,89724$27.2 million$1,131,3755,764
    ProgramApproval yearsCohort ageLoansCharged offCharge-off rate (count)Charged-off dollars / approved dollarsAverage months to charge-off
    7(a)FY2010 to FY2016seasoned (10 to 16 years)1591811.3%6.5%70
    7(a)FY2017 to FY2019maturing (7 to 9 years)6046.7%5.6%84
    7(a)FY2020 to FY2023young (3 to 6 years)5811.7%0.7%65
    7(a)FY2024 to FY2026new (under 3 years)2300.0%0.0%n/a
    504FY2010 to FY2016seasoned (10 to 16 years)1000.0%0.0%n/a
    504FY2017 to FY2019maturing (7 to 9 years)400.0%0.0%n/a
    504FY2020 to FY2023young (3 to 6 years)900.0%0.0%n/a
    504FY2024 to FY2026new (under 3 years)100.0%0.0%n/a

    Sawmills carry more credit risk than wood products as a whole. Of 159 sawmill 7(a) loans approved in FY2010 to FY2016, 18 were charged off (11.3% by count, 6.5% of dollars), on average 70 months after approval, against 7.1% for all wood products and 6.4% for all manufacturing [6]. The sample is small, but the direction is clear and matches the lumber price cycle: losses arrived about six years after approval on average, not in the first year.

    NAICSIndustry group7(a) loans FY2010-26504 loans FY2010-26SBA loans FY2020-26Average SBA loan FY2020-267(a) FY2010-16 charged off
    3211Sawmills and wood preservation34125104$732,03520 of 174 (11.5%)
    3212Veneer, plywood and engineered wood1483854$953,2638 of 80 (10.0%)
    3219Other wood products1,782325808$857,25644 of 761 (5.8%)

    USDA activity, all states

    USAspending counts awards by program, not industry: 643 B&I guaranteed loan awards from 1 October 2023 to 30 September 2026, shown for the ten states with the most [13]. Timber Production Expansion guarantees use a separate assistance listing (10.385) and are not in this count [2].

    StateB&I guaranteed loan awardsREAP grantsREAP guaranteed loansCommunity Facilities awards
    Missouri74309432
    Texas72134340
    Oklahoma37103047
    California3593551
    North Carolina331021287
    Louisiana2872022
    New York281861393
    Florida2467121
    Illinois21459637
    Ohio21268075
    All 51 states with data6436,722751,717

    Financing structure: guarantees, fees, equity and collateral

    FY2026 loan typeGuarantee feeAnnual retention feeGuaranteeExtra fee if guarantee issued before construction completion
    B&I under $5 million3.0%0.55%85%0.50%
    B&I $5 million to $25 million3.0%0.55%80%0.50%
    B&I reduced fee1.0%0.50%80%0.50%
    B&I Alaska high-cost isolated area not on road system1.0%0.50%90%0.50%
    Community Facilities guaranteed1.25%0.50%80%0.50%
    REAP guaranteed1.0%0.25%80%0.50%

    The B&I guarantee fee is loan times guaranteed percentage times rate, and the retention fee is charged yearly on the guaranteed share of principal outstanding [1][7]. Rates are negotiated, fixed or variable; the term follows the useful life of the collateral up to 40 years, fully amortising [1]. Mill equipment wears faster than buildings, so a mill loan usually blends a 10 to 15 year equipment term with a longer real estate term.

    Borrower situation at closingMinimum capital or equity (any one test)Rule
    Existing business10% balance-sheet equity (or debt to equity no more than 9 to 1); or 10% of total eligible project costs invested; or owner capital of at least 10% of net fixed assets plus depreciation5001.105(d)(1)
    New business with sales contracts covering debt service for at least the loan term10% balance-sheet equity (or 9 to 1); or 10% of project cost5001.105(d)(2)
    New business, construction, guarantee requested before completion25% balance-sheet equity (or 3 to 1); or 25% of project cost5001.105(d)(3)
    All other new businesses20% balance-sheet equity (or 4 to 1); or 25% of project cost5001.105(d)(4)
    Higher-risk loansAgency may raise the requirement (industry status, concentration, collateral, guarantees, cash flow, contracts, credit rating, strength of the feasibility study, management)5001.105(d)(5)

    Equity must be cash or earning assets, not appraisal surplus, and goes in before guaranteed funds when the guarantee is issued during construction [1]. Real estate over $250,000 needs a USPAP appraisal; going concern value is deducted before discounting [1]. A mill is a special-purpose property whose liquidation value depends on the log supply that justified it, so lenders typically discount mill equipment and the equity plan should expect it.

    Timber Production Expansion compared with B&I

    Feature, on a $12,000,000 loanB&I, FY2026Timber Production Expansion
    Guarantee80% ($9,600,000)90% ($10,800,000)
    Lender's unguaranteed exposure$2,400,000$1,200,000
    Up-front guarantee fee3.0% of the guaranteed amount ($288,000)None
    Annual retention fee, year 10.55% of guaranteed balance ($51,616)None
    Maximum loan$25 million per borrower$25 million per borrower, including dependent affiliates
    Location testRural area under 5001.3Within 250 miles of high or very high priority National Forest System land
    Raw materialNo requirementRestoration byproducts from Federal or Tribal priority land; a significant amount of raw material from Federal or Tribal land
    Application timingOngoing; priority scoring when funds are shortFirst come, first served until funds are used
    Rules7 CFR 50017 CFR 5001 as modified by the notice

    On a $12,000,000 loan, Timber Production Expansion saves about $288,000 of up-front guarantee fee and about $51,616 of retention fee in year one, and halves the lender's unguaranteed exposure [2][7]. The cost is eligibility: the mill must sit near priority Federal or Tribal land and draw a significant share of its raw material from it, which ties the business to the pace of federal restoration sales.

    Priority points a mill can document

    B&I priority factor (5001.318, maximum 100 points)PointsWhat the study can document
    Project in an unincorporated area or a city under 25,0005Mill address
    Distressed community (EIG index); persistent-poverty rural county; unemployment at least 125% of the state rate; tribal land5 eachCounty data
    Rate at or below Prime + 1.5%; guaranteed loan under 60% of project cost; veteran-owned5 eachRate quote, sources and uses
    Industry not already present in the community5Local employers by NAICS
    20% or more of sales in international markets5Export sales (hardwood, chips)
    Locally owned and managed5Ownership chart
    Natural resource value-added product5Lumber, timbers, chips and pellets from logs
    At least five jobs created or saved at an average wage above 150% of the federal minimum wage5Staffing plan and wages
    Healthcare benefits offered to all employees, at least 50% of the premium paid5Benefits plan
    State Director or Administrator discretionary pointsUp to 10 eachStatewide distribution, emergencies, strategic plans, special initiatives; loans over $10 million

    A sawmill qualifies on its face for the natural resource value-added point, and a locally owned and managed mill making a product from a natural resource meets one of the criteria for B&I's reduced guarantee fee [1].

    Worked examples (illustrative)

    Two illustrative loans at an assumed 7.50% fixed rate: Example A, a $4,000,000 modernization over 15 years in the 85% B&I tier, and Example B, a $12,000,000 new or restarted mill over 20 years in the 80% tier. Neither is a quote or a past project.

    Example A: $4,000,000 mill modernization, 85% guarantee

    ItemIllustrative valueBasis
    Loan amount$4,000,000Illustrative modernization of an existing mill (new saw line and kilns)
    Rate and term7.50% fixed, 15 years, monthly paymentsAssumption within 5001.401 and 5001.402
    FY2026 guarantee85%: $3,400,000 guaranteed, $600,000 notB&I under $5 million: 85%
    Guarantee fee$102,000 (3.00%); $119,000 if the guarantee is issued before construction is completeLoan x guarantee % x fee rate; 5001.454
    Monthly payment / annual debt service$37,080 / $444,966Level amortisation, no balloon
    Retention fee, year 1 / year 10$17,998 / $8,6510.55% x guaranteed principal outstanding; 5001.455
    NOI for 1.00x / 1.25x$444,966 / $556,207Debt service x coverage
    NOI for 1.25x with the retention fee$578,706(Debt service + year-1 retention fee) x 1.25
    New business: 25% of project cost testCost $5,333,333; equity $1,333,3335001.105(d)(3) and (4)
    New business: 20% balance-sheet testAssets $5,000,000; equity $1,000,0005001.105(d)(4)
    Existing business: 10% of project cost testCost $4,444,444; equity $444,4445001.105(d)(1)

    Example B: $12,000,000 new or restarted mill, 80% guarantee

    ItemIllustrative valueBasis
    Loan amount$12,000,000Illustrative new or restarted mill
    Rate and term7.50% fixed, 20 years, monthly paymentsAssumption within 5001.401 and 5001.402
    FY2026 guarantee80%: $9,600,000 guaranteed, $2,400,000 notB&I $5 million to $25 million: 80%
    Guarantee fee$288,000 (3.00%); $336,000 if the guarantee is issued before construction is completeLoan x guarantee % x fee rate; 5001.454
    Monthly payment / annual debt service$96,671 / $1,160,054Level amortisation, no balloon
    Retention fee, year 1 / year 10$51,616 / $35,8340.55% x guaranteed principal outstanding; 5001.455
    NOI for 1.00x / 1.25x$1,160,054 / $1,450,068Debt service x coverage
    NOI for 1.25x with the retention fee$1,514,587(Debt service + year-1 retention fee) x 1.25
    New business: 25% of project cost testCost $16,000,000; equity $4,000,0005001.105(d)(3) and (4)
    New business: 20% balance-sheet testAssets $15,000,000; equity $3,000,0005001.105(d)(4)
    Existing business: 10% of project cost testCost $13,333,333; equity $1,333,3335001.105(d)(1)

    Example A needs about $556,207 of net operating income for 1.25 times coverage; Example B about $1,450,068. A new business borrowing Example B must commission an independent study and would put in about $4,000,000 under the 25% of project cost test [1]. Under Timber Production Expansion the same Example B loan would carry a 90% guarantee and no fees [2].

    Margin per thousand board feet the debt requires

    Annual lumber output, million board feet (assumed)NOI per MBF for 1.25x, Example ANOI per MBF for 1.25x, Example BNOI effect of a $10 per MBF change in lumber price or log cost
    10$56$145$100,000
    20$28$73$200,000
    30$19$48$300,000
    50$11$29$500,000

    At an assumed 20 million board feet a year, Example A needs about $28 of net operating income per MBF; at 30 million, Example B needs about $48. The last column is the sensitivity that matters: every $10 per MBF of lumber price or log cost moves income by that amount, which is why the study runs price scenarios rather than one average.

    Stress test and break-even

    ScenarioExample A NOIExample A coverageExample B NOIExample B coverage
    Base case at 1.25x$556,2071.25x$1,450,0681.25x
    NOI down 10%$500,5871.12x$1,305,0611.12x
    NOI down 20% (break-even)$444,9661.00x$1,160,0541.00x
    NOI down 30%$389,3450.88x$1,015,0470.88x
    Lumber price $25 per MBF lower at 20 MMBF (A) and 30 MMBF (B)$56,2070.13x$700,0680.60x
    Lumber price $50 per MBF lower at 20 MMBF (A) and 30 MMBF (B)$-443,793-1.00x$-49,932-0.04x
    Variable rate 2 points higher, re-amortised$556,2071.11x$1,450,0681.08x

    A $25 per MBF fall in lumber price, with logs unchanged, takes Example A to 0.13x and Example B to 0.60x coverage. The study should run the mill's own price history through the model, include a period like the worst year in that history, and show whether the mill survives it with reserves.

    Sawmill risks, regulators and how the study tests them

    RiskRule or regulatorHow the study tests it
    Lumber price cycleNone; market riskPrice history by product; downturn case; reserves
    Log supply and priceForest Service sale program; state forestry agenciesWood basket inventory and growth; contracts; competing demand
    Overcapacity in the wood basket5001.118(b) over $1 million and 50 jobs [1]Regional mill capacity and log demand
    Fire, dust and machine safetyOSHA 1910.265 for sawmills, including dry kilns and log yards [8]Safety program, fire protection, insurance quotes
    Air and stormwater permitsState agencies; environmental review under 7 CFR 1970 [1]Permit path for boilers and kilns; log yard runoff plan
    Residual market lossNone; market riskTwo outlets per residual; haul cost; disposal cost if outlets close
    Federal raw material dependence (Timber Production Expansion)Notice conditions [2]Restoration sale schedule; alternative private supply
    Equipment and ramp-up5001.205(e)(2) for early guarantees [1]Vendor schedule, commissioning, ramp curve, working capital
    LaborState wage lawCommute-shed labor force; wage stress

    Process, timeline, documents and common review failures

    The path runs from eligibility and program choice (B&I, Timber Production Expansion or both) to lender engagement, study and appraisal, the lender's credit analysis, application to the State Office, conditional commitment, closing and the loan note guarantee. The borrower must take no action that could harm the environment or limit alternatives until USDA's environmental review is complete [1]. On this site's schedule, the data request goes out within 48 hours of signing, market work runs in weeks 2 to 4, the model and draft in weeks 4 to 6, and delivery with one round of revisions in weeks 6 to 8, with revisions at no added cost until USDA or the lender accepts the report [14][15].

    Documents the lender and Agency will look for: mill and affiliate financial statements with global cash flow; a pro forma closing balance sheet showing equity [1]; log supply agreements and timberland or sale data; lumber and residual buyer letters; equipment quotes, layout and budget; permit applications; insurance quotes; and resumes of the mill manager and 20% owners.

    Common review failures in sawmill studies

    • One lumber price applied to every year, with no downturn case.
    • Log supply described by forest area rather than by volume, species, ownership and competing demand.
    • Overrun or recovery taken from a brochure instead of comparable mills.
    • Residual revenue assumed with no named buyer or haul cost.
    • Kiln capacity smaller than sawing capacity, or drying costs left out.
    • No 5001.118(b) analysis for a mill adding more than 50 jobs [1].
    • A Timber Production Expansion application with no evidence of the 250-mile proximity or Federal or Tribal raw material [2].

    Sawmill and wood products feasibility study pages by state

    The site has 44 state pages for sawmills and wood products, each with the state's establishment, rural and SBA data. They are listed by the number of wood products establishments.

    State pageWood product establishments, 2023Change since 2019Non-metro shareSBA 7(a) and 504 loans, FY2020 to FY2026
    California1,029-3.5%5.8%98
    Pennsylvania981+0.4%39.6%32
    Texas767-1.0%15.4%46
    Ohio573+1.8%53.0%64
    North Carolina558-7.2%35.0%21
    Florida555+5.7%6.7%44
    Indiana516+1.6%42.4%23
    Georgia464-7.6%45.6%29
    Michigan462-2.5%42.6%38
    New York446-8.0%23.6%43
    Missouri412-6.2%63.0%30
    Virginia411-6.2%49.7%7
    Oregon388-7.0%25.7%27
    Illinois380+3.0%17.3%27
    Kentucky358+0.8%70.6%12
    Alabama347+4.2%45.0%5
    Minnesota315-10.0%33.8%53
    South Carolina234+3.1%31.3%18
    Mississippi210-10.6%75.0%7
    Colorado201-12.6%24.4%30
    Arizona184-1.1%6.7%26
    Utah184+0.0%14.3%35
    New Jersey178+7.9%0.0%20
    Maine174+3.0%55.6%15
    Louisiana163-2.4%41.6%6
    Massachusetts152-12.1%2.6%14
    Montana149+9.6%60.6%4
    West Virginia143+3.6%76.7%1
    Iowa138-5.5%41.1%5
    Maryland123+13.9%8.3%11
    New Hampshire109+0.9%67.0%3
    Oklahoma104-4.6%43.5%4
    Connecticut96-1.0%19.8%10
    Vermont91-10.8%86.2%7
    Kansas80-9.1%27.5%12
    Nevada68+9.7%5.0%6
    Nebraska64-3.0%21.6%5
    South Dakota57-9.5%33.3%7
    New Mexico45-16.7%17.4%5
    Alaska41+2.5%28.1%2
    Rhode Island32+6.7%0.0%5
    Wyoming32-3.0%82.4%0
    North Dakota27+3.8%15.0%3
    Delaware13+0.0%45.5%2

    Establishments and non-metro share from County Business Patterns 2023 for NAICS 321; SBA loans by project state [3][6].

    Hiring a sawmill feasibility study consultant

    An independent qualified consultant acceptable to the Agency is required for a B&I or Timber Production Expansion loan over $1,000,000 to a new business, with scope set by the Agency [1][2]. Independence rules out the equipment vendor, the log supplier and owners. A USDA feasibility study consultant on this site scopes each engagement against the program the mill will use, and coordinates with the forester or timber cruiser, the engineer and the appraiser rather than replacing them.

    The engagement includes all five Part 5001 components, a five to ten year projection with sensitivity analysis, market area and demand analysis, a competitive supply inventory, comparable operator benchmarks, a management assessment, PDF and Word reports with an Excel workbook, kickoff and midpoint calls, one round of revisions and a written acceptance guarantee; environmental assessments, engineering, legal work and appraisals are separate [14]. You provide log supply information, equipment and site plans, buyer letters, the budget and the operating history of the mill or its managers.

    Fees on the cost page: $6,900 to $12,500 for standard B&I studies, $10,500 to $14,500 for complex ones (loans over $10 million, phased or limited comparable data) and $9,500 to $18,000 for cross-program OneRD engagements such as B&I with Timber Production Expansion; timeline 6 to 9 weeks, or 3 to 4 weeks on a rush basis at a 20% to 35% premium [14]. A senior analyst responds within one business day with a scoped proposal or follow-up questions [15].

    Request a scoped proposal for your sawmill feasibility study at the contact page.

    Program examples, honestly labelled

    The site's case study Sawmill Feasibility Study for USDA Financing: Hardwood Mill Modernization in the Pennsylvania Wilds (B&I, $2M to $15M) shows the structure of a hardwood mill study [16]. The site's state guides also report these USDA-backed wood projects from Rural Development releases and lender announcements, repeated as the site states them [17]:

    ProgramBorrower and placeYearAmountPurpose
    Timber Production ExpansionTamarack Mill LLC, New Meadows, Idaho2026$9,000,000Sawmill
    Timber Production ExpansionBerg Reinvigorations LLC, Montgomery County, Kansas2026$1,725,500Sawmill; 8 jobs created, 7 retained
    Timber Production ExpansionMaine Plywood USA, Bingham, Maine2026$11,900,000Sawmill conversion to plywood underlayment
    Timber Production ExpansionBeachcombers LLC, Antlers, Oklahoma2026$12,300,000Sawmill restart
    Timber Production Expansion and B&IClatskanie Scion LLC, Clatskanie, Oregon2026$30,000,000New sawmill
    Timber Production Expansion and B&ITahoe Forest Products LLC, Carson City area, Nevada2026$50,000,000Wood products
    B&ICamden Timbers LLC, Camden area, Arkansas2022$11,457,803Sawmill purchase and retooling, working capital
    REAP grantOwens Lumber Company, Pine Apple, Alabama2024$499,975Dry kiln replacing three kilns

    The Idaho guide reports that USDA announced $115 million of Timber Production Expansion guarantees across eight states in March 2026 [17]. The REAP grant predates the October 2026 rule, which caps efficiency grants at $250,000 and pays them after a year of results [10].

    David Miller, CPA

    USDA Feasibility, Inc.

    Frequently Asked Questions

    How much does a sawmill feasibility study cost?

    The site quotes a firm fixed fee in a written proposal. Its cost page lists $6,900 to $12,500 for standard B&I studies, $10,500 to $14,500 for complex ones such as loans over $10 million or phased projects, and $9,500 to $18,000 for cross-program work such as B&I combined with Timber Production Expansion [14]. A rush adds 20% to 35%. Fees are fixed before signing and do not escalate unless the scope changes, for example by adding a second mill.

    How long does a sawmill feasibility study take?

    Six to seven weeks for a standard B&I study and seven to nine weeks for a complex one on the site's schedule, with a three to four week rush option [14]. The data request goes out within 48 hours of signing. Log supply data, equipment quotes and buyer letters are the items that most often slow a mill study, so a sponsor who has a timber supply report and vendor quotes ready shortens the schedule.

    Do I need a feasibility study for a USDA sawmill loan?

    Yes if the loan is a B&I or Timber Production Expansion guarantee over $1,000,000 to a new business, including a restart under new ownership [1][2]. Below that, or for an established mill, the Agency may still require one when the lender's analysis is not sufficient, and lenders often ask for one on a major modernization. SBA lenders may also require a study [11].

    Who can prepare a sawmill feasibility study?

    An independent qualified consultant acceptable to the Agency, with scope set by the Agency [1]. The author should not be the equipment vendor, log supplier or an owner. Timber supply estimates usually come from a forester or cruise, engineering from licensed professionals and value from an appraiser; the study pulls their work together and gives the opinion on feasibility that appendix A requires, with the consultant's qualifications attached [9].

    How long is a sawmill feasibility study valid?

    Part 5001 sets no expiry for studies; appraisals may be no more than a year old [1], and this site works to an 18-month data recency standard [14]. Mills are price-sensitive, so an update is needed sooner if lumber prices, log prices, the equipment budget or interest rates have moved enough to change coverage, or if a key log or residual contract has changed.

    Can one study serve SBA and USDA?

    Usually yes, if it is built to the Part 5001 standard, since SBA may require a feasibility study and looks at the same market and cash flow evidence [11]. The structures differ: SBA 7(a) stops at $5 million with a 75% guarantee above $150,000, and 504 asks 10% to 20% equity, while B&I reaches $25 million in rural areas and Timber Production Expansion offers 90% with no fees [11][2]. The study can model all three.

    What is the Timber Production Expansion guarantee?

    A USDA loan guarantee pilot, administered under 7 CFR 5001, for establishing, reopening, retrofitting, expanding or improving a sawmill or other wood processing facility within 250 miles of National Forest System land rated high or very high priority for restoration [2]. It guarantees 90%, charges no guarantee or retention fees, lends up to $25 million per borrower and accepts applications first come, first served while funds last. The mill must use restoration byproducts from that land.

    Which is better for a mill, B&I or Timber Production Expansion?

    Timber Production Expansion is cheaper and safer for the lender when the mill qualifies: 90% guarantee and no fees against B&I's 80% to 85% and 3.0% fee [2][7]. B&I has no proximity or raw material condition and covers any eligible rural mill. Mills dependent on private timber, or far from priority Forest Service land, use B&I; mills buying restoration wood should test Timber Production Expansion first. The study's supply section serves both.

    Can B&I finance timberland or logging equipment with the mill?

    Yes, within limits. Forestry counts as agricultural production, which B&I finances only as part of an integrated business that also processes the product and is not eligible for Farm Service Agency loans; forestry is exempt from the 50% or $5 million cap on the agricultural production portion [1]. The timberland must be owned, operated and maintained by the borrower. The study should value the land and its sustainable harvest separately from the mill.

    What does a lender look for in log supply evidence?

    Volume by species and grade within the haul radius, who owns it, how much is already committed to other mills, and at what delivered price. Supply agreements, landowner or agency sale schedules and a timber inventory from a forester carry more weight than county forest acreage. For a large mill the study must also show the new log demand will not starve existing mills, the 5001.118(b) overcapacity test [1].

    Can REAP pay for a new dry kiln?

    Possibly, for an operating rural mill. Under the rule effective 16 October 2026, REAP grants go to completed projects with 12 months of energy data, cover at most 25% of cost and cap energy efficiency grants at $250,000 [10]. A REAP guaranteed loan can finance up-front costs. The site's guides report a $499,975 REAP grant to Owens Lumber in Alabama for a kiln that replaced three, awarded before the new caps [17].

    Does a mass timber or CLT plant fit these programs?

    It can. Timber Production Expansion lists mass timber among engineered wood products [2], and B&I finances manufacturing plants generally. Part 5001 makes projects using technology that is not commercially available ineligible and requires integrated processing systems to show technical merit [1], so a first-of-its-kind line needs operating references. The market section must show signed or likely building projects, because mass timber demand is project by project.

    What should a sawmill feasibility study consultant ask for first?

    The log supply picture, the product and residual plan, the equipment list and budget, the site and permit status, and the operating history of the people who will run the mill. Those decide program fit, whether Timber Production Expansion is possible, and the scope of the market work. The site's proposal follows a fifteen-minute call and quotes a firm fixed fee [14].

    Sources

    [1] 7 CFR part 5001, OneRD Guaranteed Loans (CFR 2026 edition, title 7 vol. 15, revised 1 Jan 2026), govinfo. https://www.govinfo.gov/content/pkg/CFR-2026-title7-vol15/xml/CFR-2026-title7-vol15-part5001.xml (accessed 11 Nov 2026)

    [2] USDA RBCS, Notice of Funding Opportunity for the Timber Production Expansion Guaranteed Loan Program for Fiscal Year 2024, 89 FR 104972 (26 Dec 2024), FR Doc 2024-30651. https://www.govinfo.gov/content/pkg/FR-2024-12-26/html/2024-30651.htm (accessed 11 Nov 2026)

    [3] U.S. Census Bureau, County Business Patterns 2019 and 2023, state and county files. https://www2.census.gov/programs-surveys/cbp/datasets/2023/cbp23st.zip ; https://www2.census.gov/programs-surveys/cbp/datasets/2023/cbp23co.zip ; https://www2.census.gov/programs-surveys/cbp/datasets/2019/cbp19st.zip (accessed 11 Nov 2026)

    [4] U.S. Census Bureau, Vintage 2025 county population estimates (co-est2025-alldata). https://www2.census.gov/programs-surveys/popest/datasets/2020-2025/counties/totals/co-est2025-alldata.csv (accessed 7 Nov 2026)

    [5] OMB metropolitan and micropolitan statistical area delineation file, July 2023 (list1_2023). https://www2.census.gov/programs-surveys/metro-micro/geographies/reference-files/2023/delineation-files/list1_2023.xlsx (accessed 7 Nov 2026)

    [6] U.S. Small Business Administration, 7(a) and 504 FOIA loan data, as of 30 Sep 2026: FOIA_7a_FY2010_FY2019, FOIA_7a_FY2020_Present, FOIA_504_FY2010_Present. https://data.sba.gov/sites/default/files/uploaded_resources/FOIA_7a_FY2020_Present_asof_260930.csv (and companion files) (accessed 11 Nov 2026)

    [7] USDA, OneRD Annual Notice of Guarantee Fee Rates, Periodic Retention Fee Rates, Loan Guarantee Percentage and Fee for Issuance of the Loan Note Guarantee Prior to Construction Completion for Fiscal Year 2026, 91 FR 11272 (9 Mar 2026). https://www.govinfo.gov/content/pkg/FR-2026-03-09/html/2026-04581.htm (accessed 6 Nov 2026)

    [8] 29 CFR 1910.265, Sawmills (CFR 2025 edition). https://www.govinfo.gov/content/pkg/CFR-2025-title29-vol5/xml/CFR-2025-title29-vol5-sec1910-265.xml (accessed 11 Nov 2026)

    [9] OneRD Guaranteed Loan Regulation, 85 FR 42494 (14 Jul 2020), appendix A to subpart D of part 5001, Feasibility Study Components, pp. 42556-42557 (published as images). https://www.govinfo.gov/content/pkg/FR-2020-07-14/html/2020-13991.htm (accessed 11 Nov 2026)

    [10] USDA RBCS, Unleashing American Energy and Economic Prosperity; Rural Energy for America Program (REAP), final rule with comment period, 91 FR 62600 (1 Oct 2026), effective 16 Oct 2026. https://www.govinfo.gov/content/pkg/FR-2026-10-01/html/2026-20178.htm (accessed 7 Nov 2026)

    [11] 13 CFR part 120, Business Loans (CFR 2026 edition), govinfo; sections 120.150, 120.151, 120.160, 120.210, 120.220, 120.801, 120.900 to 120.971. https://www.govinfo.gov/content/pkg/CFR-2026-title13-vol1/xml/CFR-2026-title13-vol1-sec120-160.xml ; https://www.govinfo.gov/content/pkg/CFR-2026-title13-vol1/xml/CFR-2026-title13-vol1-sec120-151.xml (120.151 accessed 11 Nov 2026; others accessed 6 Nov 2026)

    [12] USDA Rural Development, Amendment of Rural Development Funding Opportunities Pursuant to the Executive Order 'Ending Radical and Wasteful Government DEI Programs and Preferencing', 90 FR 13580 (25 Mar 2025), FR Doc 2025-04988. https://www.govinfo.gov/content/pkg/FR-2025-03-25/html/2025-04988.htm (accessed 11 Nov 2026)

    [13] USAspending.gov, award counts by place of performance for Assistance Listings 10.768 (B&I), 10.766 (Community Facilities) and 10.868 (REAP), 1 Oct 2023 to 30 Sep 2026, API v2 spending_by_award_count. https://api.usaspending.gov/api/v2/search/spending_by_award_count/ (accessed 7 Nov 2026)

    [14] usda-feasibility-study.com, USDA Feasibility Study Cost & Timeline (site page, as captured 7 Nov 2026). https://usda-feasibility-study.com/usda-feasibility-study-cost

    [15] usda-feasibility-study.com, Contact & Request a Proposal (site page, as captured 7 Nov 2026). https://usda-feasibility-study.com/contact

    [16] usda-feasibility-study.com, Case Studies (site page, as captured 7 Nov 2026). https://usda-feasibility-study.com/case-studies

    [17] usda-feasibility-study.com, state USDA guides (site pages, as captured 7 to 10 Nov 2026), for precedents attributed there to USDA Rural Development releases and lender announcements. https://usda-feasibility-study.com/states

    Ready to Start Your USDA Project?

    Get your free consultation today and take the first step toward securing USDA funding for your rural development project.

    Our USDA feasibility study consultants scope every engagement against the five Part 5001 components in a free consultation.

    Get Your Free Consultation

    Fill out the form below and we'll contact you within 24 hours to discuss your project.

    We'll respond within 24 hours